STUDI PEMANFAATAN FLY ASH PEMBANGKIT LISTRIK TENAGA UAP (PLTU) BATUBARA MENJADI BATAKO

Taufiqurrahman Hafiizh, Dr. Ir. Yunita Ismail Masjud, M.Si

Abstract


Abstract. Coal-Fired Power Plant (CFPP) owned by PT. XYZ is located in Babelan , Bekasi Regency. Coal for CFPP is expected to continue to increase every year, so that the amount of fly ash produced will also increase. Fly ash are sources that have the potential to have a negative impact on the surrounding environment. Utilization or processing of fly ash can have a positive impact, including being used as a supplement in the production of concrete, both for mortar and mortar mixes. Objectives: The Objective of this research is how the composition of fly ash influences in the manufacture of bricks on the dimensions of, compressive strength and water absorption and whether they meet the quality requirements of bricks based on SNI 03-0439-1989. Methods and Results: The method applied in this study was make 5 different treatments of bricks with different compositions, making bricks using a manual brick molding tool for hollow bricks, then from the results of the molded bricks made and then dried until 28 days old and continued with dimension measurements, compressive strength, and water absorption capacity The findings indicated that the dimensions of the fly ash bricks remained within.the acceptable tolerance limit. Among the fly ash bricks tested, one exhibited the.highest compressive strength at 80.48 Kg/Cm2, coupled with the highest water absorption capacity recorded at 7.43%. Conclusion: It is recommended that during the mixing process, great care should be taken to ensure the mixture achieves homogeneity, ensuring thorough and even mixing It is advisable to employ a hydraulic machine to facilitate this process, leading to denser brick molding outcomes.


Keywords


Fly Ash; Power Plant; Coal; Concrete Brick; SNI 03-0349-1989

References


Sjoraida, D. F., & Rizal, E. (2019). Penerimaan Masyarakat Sebagai Hasil Sinergi Humas Dan Media Massa. Temali: Jurnal Pembangunan Sosial, 2(1), 61-76.

Asof, M., Arita, S., Mukiat, M., Luthfia, L., Andalia, W., & Naswir, M. (2022). Article_Analisis Karakteristik, Potensi dan Pemanfaatan Fly Ash dan Bottom Ash PLTU Industri Pupuk. Jurnal Teknik Kimia.

Ayuningtyas, U., Susila, I. M. A. D., Sihombing, A. L. S., Sasongko, N. A., Anggraeni, P., Nugroho, T. P. A., & Darmayanti, N. T. E. (2022, December). PEMANFAATAN FLY ASH DAN BOTTOM ASH SEBAGAI MATERIAL KONSTRUKSI RAMAH LINGKUNGAN DALAM RANGKA MENDUKUNG KRITERIA BANGUNAN HIJAU. In PROCEEDINGS OF NATIONAL COLLOQUIUM RESEARCH AND COMMUNITY SERVICE (Vol. 6, pp. 51-56).

Wigusti, A. E., Widyaningrum, A., Puspita, K. E., Trianingrum, S., Rosyidah, U., & Sofiyah, S. (2022). IMPLEMENTASI KONSEP CREATING SHARED VALUE (CSV) DALAM PEMANFAATAN FLY ASH BOTTOM ASH (FABA) OLEH PLTU JATENG 2 ADIPALA OMU. Jurnal Ilmiah MEA (Manajemen, Ekonomi, & Akuntansi), 6(2), 1930-1946.

Silaban, D. P., & Ola, A. L. (2019). Limbah Fly Ash Pabrik Minyak Nabati sebagai Bahan Substitusi Semen dalam Pembuatan Batako. Jurnal Penelitian Teknologi Industri, 11(1), 30-38.

Ni'mah, L., Syauqiah, I., Mirwan, A., Wicakso, D. R., & Wijayanti, H. (2019). Batako dari limbah botol plastik: tinjauan kuat tekan. AL-ULUM: JURNAL SAINS DAN TEKNOLOGI, 5(1), 26-29.

Mufika, N. R., Dewi, S. M., & Arifi, E. (2018). Pengaruh Penggunaan Beton Plastik Untuk Batako Ringan Berlubang Diuji Terhadap Kuat Tekan Dan Kuat Lentur Dengan Variasi Jumlah Serat Benang. Jurusan Teknik Sipil, Fakultas Teknik, Universitas Brawijaya.

Arif, M. (2021). Pemanfaatan Limbah Tailing Pertambangan Untuk Bahan Campuran Pembuatan Batako Untuk Pengurangan Prosentase Penggunaan Semen (Doctoral dissertation, Universitas_Muhammadiyah_Mataram).

Vilpa, A. (2021). Pengaruh Penggunaan Limbah Cangkang Kerang Sebagai Pengganti Agregat Halus Terhadap Kuat Tekan Dan Daya Serap Air Pada Batako (Doctoral dissertation, Universitas Islam Riau).

Syafiâ, A., Purnomo, Y. C. S., & Krisnawati, L. D. (2018). Pemanfaatan Serbuk Kaca Dari Jenis Kaca Bening Dengan Ketebalan 3-4 mm Sebagai Bahan Tambah Dalam Pembuatan Batako. Jurnal Manajemen Teknologi dan Teknik Sipil (JURMATEKS), 1(1), 44-55.

Julianda, A. (2022). Analisis Pengaruh Variasi Serat Plastik terhadap Kekuatan Tekan dan Impak dalam pembuatan Batako (Doctoral dissertation, Universitas Medan Area).

Hamdi, F., Lapian, F. E. P., Tumpu, M., Mabui, D. S. S., Raidyarto, A., Sila, A. A., & Rangan, P. R. (2022). Teknologi Beton. Tohar Media.

WIBISONO, H. (2023). Pengaruh Sekam Padi Sebagai Agregat Pada Batako Dengan Penambahan Abu Batu Dan Fly Ash Terhadap Aspek Teknis, Biaya Produksi, Dan Redaman Suara.

PRASETYO, A. (2022). Pengaruh Fly Ash Pada Batako Terhadap Kuat Tekan, Penyerapan Air Dan Redaman Suhu (The Effect Of Fly Ash In Brickwork On Compressive Strength, Water Absorption And Thermal Insulation).




DOI: http://dx.doi.org/10.33021/jenv.v9i1.4763

Copyright (c) 2024 Taufiqurrahman Hafiizh

Creative Commons License
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

Journal of Environmental Engineering and Waste Management Published by PresUniv Press, in collaboration with IESA and APIK Indonesia Network